SH2030 + NUCLEO64 + USB

49,00

D7A v1.1 FSK / MSK shield with chip antenna operating in the 863-870 MHz ISM + Nucleo-L152RE development board for MBED + Mini USB cable to power up your Nucleo Board and program it. Fully compatible with the GW2120.

Description

SH2030 Description

D7A v1.1 FSK / MSK shield operating in the 863-870 MHz ISM band for Nucleo 64 and Arduino boards based on WM1030 (SP1ML) with integrated antenna for optimal footprint. Datasheet

Who should buy it?

You should buy it if:

  • You want to evaluate the DASH7 Alliance Protocol (D7A).
  • You want to deploy a D7A network to connect your custom made objects to the DASH7Board
  • You want to prototype your sensor application using MBED and use D7A to communicate.

Software

The shields are fully programmed an configured with WizziLab’s D7A v1.1 stack. A procedure to upgrade the code when new releases of the stack is available.

An application example including the shield driver in source are available on MBED to program your application on the Nucleo board (D7A_1X_demo).

Documentation

General Statement about radio emission

The WizziKit is intended for use for ENGINEERING DEVELOPMENT, DEMONSTRATION OR EVALUATION PURPOSES ONLY and is not considered by WizziLab to be a finished end product fit for general consumer use. It generates, uses, and can radiate radio frequency energy. Operation of the equipment may cause interference with radio communications, in which case the user at his own expense will be required to take whatever measures may be required to correct this interference.

Any use of radio frequencies and/or power availability of the WizziKit and its development application(s) must comply with local laws governing radio spectrum allocation and power limits for this evaluation module. It is the user’s sole responsibility to only operate this kit in legally acceptable frequency space and within legally mandated power limitations. Any exceptions to this is strictly prohibited and unauthorized by WizziLab unless user has obtained appropriate experimental/development licenses from local regulatory authorities, which is responsibility of user including its acceptable authorization.

STM32L152

The STM32 Nucleo board provides an affordable and flexible way for users to try out new ideas and build prototypes with any STM32 microcontroller line, choosing from the various combinations of performance, power consumption and features.

The Arduino™ connectivity support and ST Morpho headers make it easy to expand the functionality of the STM32 Nucleo open development platform with a wide choice of specialized shields.

The STM32 Nucleo board does not require any separate probe as it integrates the ST-LINK/V2-1 debugger/programmer.

Microcontroller features

  • STM32L152RET6 in LQFP64 package
  • ARM®32-bit Cortex®-M3 CPU
  • 32 MHz max CPU frequency
  • VDD from 1.65 V to 3.6 V
  • 512 KB Flash
  • 80 KB SRAM
  • 16 KB EEPROM
  • GPIO (51) with external interrupt capability
  • 12-bit ADC with 21 channels
  • RTC
  • Timers (9)
  • I2C (2)
  • USART (5)
  • SPI (3)
  • USB 2.0 full-speed
  • DAC (2)
  • LCD (1) 4×32 or 8×28
  • Operationnal Amplifiers (2)
  • Comparators (2)

Nucleo features

  • Two types of extension resources
    • Arduino Uno Revision 3 connectivity
    • STMicroelectronics Morpho extension pin headers for full access to all STM32 I/Os
  • On-board ST-LINK/V2-1 debugger/programmer with SWD connector
    • Selection-mode switch to use the kit as a standalone ST-LINK/V2-1
  • Flexible board power supply
    • USB VBUS or external source (3.3 V, 5 V, 7 – 12 V)
    • Power management access point
  • User LED (LD2)
  • Two push buttons: USER and RESET
  • USB re-enumeration capability: three different interfaces supported on USB
    • Virtual Com port
    • Mass storage (USB Disk drive) for drag’n’drop programming
    • Debug port